Shield Coax
Triax Cables can Improve On-Wafer Parametric Testing
In wafer level DC measurements, anticipating the signal magnitudes makes it easier to assess potential sources of error. For simplicity, let's assume all of the signals being measured are neither high voltage (i.e., greater than 100V) or high current (greater than 200mA). We can break down the error sources into four categories: leakage currents, electrostatic interference, mechanical effects, and test lead resistance.
Leakage currents. These are currents flowing through paths other than intended signal paths, such as current flowing through insulator materials that are part of interconnections. This leakage current can be a problem when the impedance of the device under test (DUT) is similar to that of the various insulators in the circuit. The simplest fix is to use a high quality cable with high resistance insulation such as Teflon® or polyethylene. Better quality cables often reduce the effects of dielectric absorption, which is typically a function of their high impedance insulation material.
Although high quality cables can go a long way towards reducing leakage currents, they may not always be sufficient. It's important to understand the nature of the leakage path in a shielded Coaxial Cable when it's used for the connection between a typical DC instrument, such as a source-measure unit (SMU), and the DUT. Leakage current flows from the center conductor to the shield through the cable's insulation resistance. This causes the SMU to measure the sum of the current flowing through the DUT and the leakage current, rather than just the current flowing through the DUT.
A technique called guarding can eliminate the effects of leakage currents flowing through the insulation. A guard is a low-impedance point in the circuit that's at the same potential as the high-impedance lead in the circuit. In a guarded measurement, the shield is driven to the same potential as the Force Hi output terminal of the SMU using a unity-gain, low-impedance amplifier (guard). Therefore, no leakage current flows through the insulation resistance.
This technique requires a third (GUARD) connection on the instrument in addition to the usual cable shield and signal conductor. Although it's theoretically possible to use a guarded connection on a coaxial cable, it would be unsafe because the shield would be at the same potential as the Force Hi output terminal. The GUARD of an SMU should never be connected to the shield of a coaxial cable. The correct solution is to use a triaxial cable. Its inner shield is connected to the GUARD terminal of the instrument, and the outer shield is connected to the Force LO output terminal.
Electrostatic and magnetic interference (EMI). EMI occurs when electrically magnetically charged objects disturb the circuit under test. Although these effects are negligible at low impedances (because the charges dissipate quickly) that doesn't hold true at high impedances. Typically, the sources of EMI are environmental, such as fluorescent lights, motors, and even people. EMI-induced errors are generally due to some type of capacitive coupling into the circuit, which can create an extra current defined by this equation:
I = C(dV/dt) + V(dC/dt)
Errors due to electrostatic coupling can be minimized in two ways. The first is to use shielded triaxial cables. Another really effective way to reduce electrostatic interference is to connect the prober's head plate, dark box, or metal enclosure to ground so the induced current noise will flow through the shield to ground and not through the DUT.
Although grounding the prober's enclosure or head plate is a good way to reduce electrostatic interference, doing it poorly can make matters worse. Typically, the prober and instrument are connected to two separate power line grounds because they are usually connected to separate power outlets. In that setup, a fluctuating current can flow between the instrument and the probe station, causing the instrument's ground unit or low connection to move, producing errors. These are known as ground loops; to prevent them, the prober enclosures and shield should be connected to a common ground in the test circuit.
Mechanical effects. Triboelectric and piezoelectric effects are also significant sources of DC measurement errors. Triboelectric currents are generated due to charges created by friction between a conductor and insulator. The Friction causes free electrons to be rubbed off the conductor, creating a current charge imbalance that generates current flow. This effect is noticeable when low quality cables are flexed. The insulators of high quality cables are usually coated with a lubricating layer of graphite that minimizes friction. Even high quality triax cables need isolation from vibration, which can cause some current flow due to piezoelectric effects. Placing a prober on an air table and using remote pre-amps to minimize triax cable lengths can help minimize these problems.
Errors due to two-wire test lead connections. No matter how good the test cable, losses through it can still be significant. The conductor resistance of most interconnect cables is only a few ohms for even a very long length. However, when the resistance of the DUT is also relatively low (e.g., a metal structure), the resistances contributed by cables and pad contacts can cause large errors if the instrument is connected to the DUT using two-wire connections. For example, if the resistance of the cables, contacts, and DUT are at single ohm levels, then the meter will measure the sum of these resistances.
Fortunately, four-wire or Kelvin connections offer a way to solve the problem of losses due to voltage drops across Interconnect Cable conductors. In a Kelvin connection arrangement, a voltmeter is connected right at the DUT while a current source stimulates the DUT. An SMU offers both source and measurement capabilities, and can calculate resistance from I-V measurements using two different sets of leads for its current source and voltmeter circuits. With this arrangement, given that the SMU's voltmeter circuit has high input impedance, very little test current will be diverted to this part of the instrument. Therefore, the source current is essentially the same at all points in the test circuit and the voltmeter measures only the voltage drop across the DUT and contact resistance, but not the conductor resistance of the interconnect cabling.
Cabling for C-V measurements. Semiconductor C-V measurements are typically performed using a multi-frequency capacitance meter with four terminals: high current (Hcur), high potential (Hpot), low current (Lcur), and low potential (Lpot). These terminals are coaxial, so they normally require a coaxial interconnect cable, but can also use the appropriate triaxial cable. The instrument terminals also have fixed characteristic impedance, typically 50 or 100 ohms. A multi-frequency capacitance meter measures impedance by sourcing a small AC voltage across the DUT and measuring the resulting AC current and AC voltage.
The signals used to measure capacitance are AC, so take care that the signal paths minimize impedance changes, which will generate signal reflections that can impact the AC source and measured signals, causing erroneous results. Using cables with the same characteristic impedance as the instrument can help minimize impedance changes. Also, most capacitance meters perform some form of cable compensation, which involves entering the length of the cables being used into the meter setup. In addition, all four cables must be the same length to minimize impedance changes in the signal path and ensure the meter's cable compensation calculations are correct. Improperly shielded coaxial cables can also cause errors in capacitance measurements, so check that the cables' shields are not open.
Stray cabling and interconnect inductances can cause resonances in the test circuit, which may also produce erroneous capacitance measurements. Reduce the inductance by connecting the shields of the coaxial cables as closely as possible to the DUT to isolate the inductance from the measurement.
Cabling challenges for ultra-fast DC and pulse measurements. These measurements involve signals in the AC or high frequency domain, which requires different considerations about the interconnect compared with DC or C-V measurements. Fourier series analysis shows us that no matter the speed of a pulse, it can be modeled as a series of sinusoids of varying amplitudes and frequencies. If the signal path can't pass higher frequencies accurately, some fundamental frequencies are affected, distorting the shape of the pulse and affecting the power transmitted to the DUT. Therefore, pulse testing requires a signal path with a higher bandwidth (approximately 150MHz) than either DC or C-V testing.
Pulse generators don't typically include measurement capabilities and oscilloscopes don't include a stimulus source. The test connections on these instruments are single-ended; i.e., the center conductor carries the signal and is connected to the DUT. The shield of the coaxial cable is the return path for the signal and ideally should be connected to the low terminal of the DUT. Today, however, a new class of pulse instruments does offer measurement capabilities, but even these instruments use a single coaxial cable to the probes for each channel. To prevent reflections, the interconnect's impedance should match that of the source. Most pulsing instruments have a 50-ohm input impedance so one normally uses 50-ohm coaxial cables when connecting to them. To minimize inductances, it's a good practice to connect the shields of multiple coax cables together.
Ideally, to ensure the entire signal path is free of impedance changes or insertion losses, the shield of the coaxial cable should be connected to the low side of the test circuit. And while connecting the low side of the DUT to DC ground will work, the return signal may then follow two paths back to the instrument: one through earth and the second through capacitive coupling to the coaxial shield. Connecting the low side of the test circuit to a DC return path will ultimately limit the fidelity of the pulse.
Different measurements – different cabling requirements. As discussed above, each measurement type requires different considerations in the selection of cabling. Up to now, performing DC I-V, C-V, and pulse testing on a DUT required cable changes when moving from one type of measurement to another. This was especially true when a switch matrix was not being used, but switch matrixes present their own set of complications.
Changing cables can be time-consuming and often requires raising and lowering the probes between tests, which risks damaging wafer pads. Fortunately, a new test kit of multi-measurement prober cables (Keithley's MMPC kit) optimized for use with Suss and Cascade probers offers a simple solution to this problem. This cable kit supports I-V, C-V, and pulsed measurements using a single set of triax interconnects. The MMPC kit has special triaxial cables and adaptors that allow both high precision DC and high bandwidth AC connections to the probes and DUT. The cables can be arranged in both Kelvin and non-Kelvin configurations. More importantly, all of this can be done without disturbing the cabling to the probes; only the cables at the prober connector bulkhead need be moved.
Although the MMPC kit was initially designed for use with Keithley's Model 4200-SCS Semiconductor Characterization System, they can be used with many other test instruments designed for wafer level device testing with Suss and Cascade probers. In addition, the Model 4225-RPM Remote Amplifier/Switch, a companion to Keithley's 4225-PMU Ultra-Fast I-V Module, automates reconfiguring MMPC cables when they are used with the Model 4200-SCS.
References:
1. A brief explanation of Fourier series analysis is available at http://en.wikipedia.org/wiki/Fourier_series.
2. More detailed information on guarding techniques can be found in Keithley's "Low Level Measurements Handbook", available online at http://www.keithley.com/knowledgecenter/knowledgecenter_pdf/LowLevMsHandbk_1.pdf.
About the Author
David Rose is Sr. staff engineer with the Semiconductor Group of Keithley Instruments in Cleveland. He received his B.S. in Electrical Engineering from Cleveland State University and has 15 years of experience in semiconductor production testing.
How to terminate Quad shield DTV Coaxial Cable
 |
 RG6 BURIAL DIRECT BURY 1000 SPOOL TRI SHIELD COAX CABLE DIGITAL FLOODED $99.99 Time Remaining: 19h 53m Buy It Now for only: $99.99 Buy It Now |
 Belden 8240 RG 58 U coax cable 50ft 95 Braid Shield NEW $19.99 Time Remaining: 3h 38m Buy It Now for only: $22.99 Buy It Now |
 RG6 Quad Shield Coax Solid Bare Copper BC 500 FT 3 ghz CATV SATV 3ghz BLACK $55.00 Time Remaining: 26d 5h 42m Buy It Now for only: $55.00 Buy It Now |
 Yellow RG6 U Quad Shield Coax Cable $105.00 Time Remaining: 25d 15h 31m Buy It Now for only: $105.00 Buy It Now |
 ISOTEC I181V6 00 RG6 Dual Shield Solid Copper Coax 1000 Black Box $45.00 Time Remaining: 23d 18h 42m Buy It Now for only: $45.00 Buy It Now |
 QTY OF 25 RG59 QUAD SHIELD PCT DRS 59L Coax Compression CONNECTORS ORANGE BN $9.49 Time Remaining: 29d 6h 42m Buy It Now for only: $9.49 Buy It Now |
 25 RG6 Quad Shield Coax Cable Compression F Connectors $16.95 Time Remaining: 19d 55m Buy It Now for only: $16.95 Buy It Now |
 20 Pack Lot F Type Compression Connector Male Plug RG6 Quad Shield Coax Cable $12.85 Time Remaining: 21d 19h 25m Buy It Now for only: $12.85 Buy It Now |
 New 25 Quad Shield Coax Cable For Satellite CATV $8.49 Time Remaining: 6d 57m Buy It Now for only: $8.49 Buy It Now |
 COAX CABLE STRIPPER TOOL RG6 RG58 RG59 Quad Shield $6.85 Time Remaining: 15d 16h 55m Buy It Now for only: $6.85 Buy It Now |
 New 50 Quad Shield Coax Cable For Satellite CATV $11.99 Time Remaining: 6d 57m Buy It Now for only: $11.99 Buy It Now |
 QTY OF 25 RG6 QUAD SHIELD PCT DRS 6QL COAX COMPRESSION CONNECTORS PURPLE BN $9.99 Time Remaining: 29d 6h 43m Buy It Now for only: $9.99 Buy It Now |
 50 FtFeetOrange Quad Shield Underground Direct Burial Rg6 Coax Coaxial Cable $28.99 Time Remaining: 24d 21h 24m Buy It Now for only: $28.99 Buy It Now |
 CATV Security Shield f RG6 RG59 Coaxial Coax Cable New $4.99 Time Remaining: 1h 20m |
 15 Foot RG6 Quad Shield Video Cable Coax Satellite HDTV $10.10 Time Remaining: 20d 12h 42m Buy It Now for only: $10.10 Buy It Now |
 RG 8X 8X RG8X MINI 8U RG8 X MINI 8 COAX DOUBLE SHIELD TINNED BRAID 36 cents p FT $3.60 Time Remaining: 18d 22h 9m Buy It Now for only: $3.60 Buy It Now |
 5 Pack Lot RG6 Quad Shield Coax Cable F Type Crimp On Connector Plug Male $4.95 Time Remaining: 21d 18h 25m Buy It Now for only: $4.95 Buy It Now |
 10 Ft Foot FeetBlack Quad Shield RG6 Digital Coax Coaxial Satellite HD TV Cable $7.89 Time Remaining: 11d 23h 51m Buy It Now for only: $7.89 Buy It Now |
 50ft Black RG6 Coax Cable Quad Shield w F Connectors GUARANTEED IN STOCK $22.44 Time Remaining: 8d 18h Buy It Now for only: $22.44 Buy It Now |
 RG11 Coax Connector RG 11 Coaxial Fitting PCT DRS 11L Compression Quad Shield $1.99 Time Remaining: 8d 48m Buy It Now for only: $1.99 Buy It Now |
 1 Foot RG6 Quad Shield Video Cable Coax Satellite HDTV $3.83 Time Remaining: 1d 9m Buy It Now for only: $3.83 Buy It Now |
 Siamese CAT5E CAT5 e RG 6 RG6 Quad Shield Coax Cable $139.95 Time Remaining: 8d 17h 14m Buy It Now for only: $139.95 Buy It Now |
 Polyethelyne Coax 95 Shield 240 Diameter 100 FEET $20.00 Time Remaining: 8d 21h 12m Buy It Now for only: $20.00 Buy It Now |
 New 100 Quad Shield Coax Cable For Satellite CATV $21.99 Time Remaining: 6d 27m Buy It Now for only: $21.99 Buy It Now |
 250 Contractors Wire Quad Shield Coax Cable NEW $45.00 Time Remaining: 16d 12h 13m Buy It Now for only: $45.00 Buy It Now |
 1000 FEET RG6 COAX CABLE PPC P6T77VVBF TRI SHIELD PERFECT FLEX CATV DISH BLACK $52.00 Time Remaining: 29d 1h 6m Buy It Now for only: $52.00 Buy It Now |
 150+ Belden 1617A RG11 Coax Cable Quad Shield 14 AWG solid 064 bare copper NR $59.00 Time Remaining: 4d 21h 34m |
 tri shield coax tri sheild stripper tool rg6 rg59 $12.00 Time Remaining: 1d 19h 29m Buy It Now for only: $12.00 Buy It Now |
 QTY OF 50 RG6 TRI SHIELD PCT DRS 6 COAX COMPRESSION CONNECTORS BLACK BRAND NEW $19.99 Time Remaining: 29d 6h 43m Buy It Now for only: $19.99 Buy It Now |
 NEW 500 FEET RG6 QUAD SHIELD COAX CABLE 18AWG 30GHZ WHITE CATV 95 COPPER $65.95 Time Remaining: 14d 21h 45m Buy It Now for only: $65.95 Buy It Now |
 CommScope Tri Shield Plenum RG6 Coax Cable 1000ft 1000 $199.00 Time Remaining: 22d 21h 20m Buy It Now for only: $199.00 Buy It Now |
 ISOTEC I181V6 09 RG6 Dual Shield Solid Copper Coax White Reel 500 $27.00 Time Remaining: 23d 18h 42m Buy It Now for only: $27.00 Buy It Now |
 4 Foot RG6 Quad Shield Video Cable Coax Satellite HDTV $5.15 Time Remaining: 4d 30m Buy It Now for only: $5.15 Buy It Now |
 Philips RG6 Quad Shield Coax 100 RV Satellite Dish $29.00 Time Remaining: 22h 8m Buy It Now for only: $29.00 Buy It Now |
 3 Ft Foot FeetWhite Quad Shield RG6 Digital Coax Coaxial Satellite HD TV Cable $4.69 Time Remaining: 12d 17h 26m Buy It Now for only: $4.69 Buy It Now |
 1000FT RG6 RG 6 COAX CABLE BOX PPC BLACK P6QVVBF QUAD SHIELD PERFECT FLEX $39.00 Time Remaining: 13d 12h 34m Buy It Now for only: $39.00 Buy It Now |
 BELDEN 9913F7 LOW LOSS DUAL SHIELD COAX 48 FT $62.60 Time Remaining: 8d 1h 50m Buy It Now for only: $62.60 Buy It Now |
 Male F Type F Connector Dual Shield RG 59 Coax Coaxial Compression Ships from US $1.65 Time Remaining: 10d 22h 42m Buy It Now for only: $1.65 Buy It Now |
 75 Ft Foot FeetBlack Quad Shield RG6 Digital Coax Coaxial Satellite HD TV Cable $21.99 Time Remaining: 12d 4m Buy It Now for only: $21.99 Buy It Now |
 Larsen NMO Antenna Mount for vehicle with 25 foot dual shield coax $14.95 Time Remaining: 6d 12h 26m |
 50 Pack Lot F Type Compression Connector Male Plug RG6 Quad Shield Coax Cable $27.95 Time Remaining: 21d 19h 25m Buy It Now for only: $27.95 Buy It Now |
 2 Foot Video Cable Coax RG6 Quad Shield Satellite HDTV $4.17 Time Remaining: 22d 14h 49m Buy It Now for only: $4.17 Buy It Now |
 20 Ft Foot FeetWhite Quad Shield RG6 Digital Coax Coaxial Satellite HD TV Cable $12.99 Time Remaining: 12d 17h 54m Buy It Now for only: $12.99 Buy It Now |
 RG6 QuadShield Quad Shield 3 GHz CATV SATV Coax 1000 $85.49 Time Remaining: 5d 15h 55m Buy It Now for only: $85.49 Buy It Now |
 50 RG6 Quad Shield Coax Cable F Compression Connectors $28.95 Time Remaining: 2d 1h 44m Buy It Now for only: $28.95 Buy It Now |
 NEW 50ft DUAL Cable BLACK RG6 Coax Shield w Ground 50 FT Coaxial w messenger $26.99 Time Remaining: 5d 16h 19m Buy It Now for only: $26.99 Buy It Now |
 Hosa DRA501 1 Meter 33 RCA RCA Dbl Shield Coax $9.49 Time Remaining: 10d 16h 32m Buy It Now for only: $9.49 Buy It Now |
 F Type Compression Connector Male Plug for RG6 Quad Shield Coax Coaxial Cable $3.39 Time Remaining: 21d 19h 24m Buy It Now for only: $3.39 Buy It Now |
 Satellite RG 6 RG6 Quad Shield Coax CMR Coaxial Cable $69.95 Time Remaining: 27d 1m Buy It Now for only: $69.95 Buy It Now |
 1000 FEET RG6 COAX CABLE PPC P6T77VVWBF TRI SHIELD PERFECT FLEX CATV DISH WHITE $32.00 Time Remaining: 11d 4h 49m Buy It Now for only: $32.00 Buy It Now |
 75 Foot RG6 Quad Shield Video Cable Coax Satellite HDTV $20.99 Time Remaining: 5d 12h 54m Buy It Now for only: $20.99 Buy It Now |
 Quad Shield RG6 Coax Cable List Price: Sale Price: $14.57 You save: $55.38 (79%)  Eligible for free shipping!Availability: Usually ships in 24 hours See Reviews For This Product DescriptionAudiovox Quad Shield Coaxial Cable HD25QC Network Cables  |
 DataShark 70018 Cable TV "F" Compression Bundle with Cable Cutter, Coax Stripper, Compression Crimper, and 10 RG6/RG6-Quad Cable TV "F" Connectors List Price: Sale Price: $37.68 You save: $22.31 (37%) Eligible for free shipping!Availability: Usually ships in 24 hours See Reviews For This Product DescriptionCompression Crimp Bundle |
 HOSA DOUBLE-SHIELD COAX, GOLD-PLATED RCAs, 2m (6.6 ft.) S/PDIF 75-W COAX List Price: Sale Price: $6.20 You save: $19.79 (76%) Eligible for free shipping!Availability: Usually ships in 24 hours See Reviews For This Product DescriptionHOSA 2M COAX CABLE - RCA |
 Thomas & Betts Snap & Seal SNS1P6 Red Rg-6 Coaxial Cable Connectors 1 Bag / 50 Count Sale Price: $26.95 Eligible for free shipping!Availability: Usually ships in 1-2 business days See Reviews For This Product |
 AUPP12 Twelve Foot Coax Cable with 2 PL-259s Sale Price: $14.99 See Reviews For This Product |
Quad Shield RG6 Coax Cable (12 feet) List Price: Sale Price: $4.70 See Reviews For This Product DescriptionTransfers signals using quad-shielded technology to preserve signal integrity 24K gold-plated studio-grade connector construction Provides optimum performance with all digital and analog devices Length: 12' |
 New CABLES TO GO 1000ft RG6/U Quad Shield Inwall Coax Cable 18AWG Copper Clad Steel Center Conductor Sale Price: $316.69 Eligible for free shipping!Availability: Usually ships in 1-2 business days See Reviews For This Product DescriptionNotice: $50 charge per refused shipment unless the refusal is based on our error. Customers should thoroughly inspect all cartons for damage before signing for the shipment.Damage: Must be reported within 15 days from delivery date... |
 Fire Shield 90814 8outlet W/Coax/Cble Surge Suppessor Strip Sale Price: $70.03 Eligible for free shipping!Availability: Usually ships in 1-2 business days See Reviews For This Product DescriptionSurge Suppressor Strips ProtectionType: Surge Number of Outlets: 8 Peripherals: Coax/ Cable/ Phone/ Fax/ Modem Protection Grade: Residential/Commercial Mount Type: Floor/Wall Mounting Amperage Rating: 15 |
 1000ft RG6/U Quad Shield InWall Coax Cbl Sale Price: $169.99 See Reviews For This Product DescriptionImpact Acoustics RG6/U Quad Shield is ideal for antenna cable television and satellite installations. This cable is 18AWG copper clad steel center conductor surrounded by a foam polyethylene dielectric... |
 Cables To Go - 43063 - 250ft RG6Q Quad Shield Coax Cable List Price: Sale Price: $51.46 You save: $7.81 (13%) Eligible for free shipping!Availability: Usually ships in 24 hours See Reviews For This Product DescriptionCables To Go RG6/U Coaxial Cable 43063 Cables |
![AmazonBasics High-Speed HDMI Cable (6.5 Feet/2.0 Meters)[Supports 3D + Audio Return Channel][OLD MODEL]](http://www.verticalmusictv.com/media/images/i/41HvrDRBhDL._SL75_.jpg)
![AmazonBasics High-Speed HDMI Cable (9.8 Feet/3.0 Meters) [Supports 3D + Audio Return Channel]](http://www.verticalmusictv.com/media/images/i/41nAsytjSsL._SL75_.jpg)
![AmazonBasics High Speed HDMI Cable (6.5 Feet / 2.0 Meters) - Supports Ethernet, 3D, and Audio Return [NEW MODEL]](http://www.verticalmusictv.com/media/images/i/417qWBWXqYL._SL75_.jpg)